What to do if my Ledger screen is frozen?

If your Ledger screen is frozen, try a hard reset, update firmware via Ledger Live, or contact support if issues persist.

Jul 11, 2025 at 12:43 am

Identifying the Cause of a Frozen Ledger Screen

When your Ledger screen is frozen, the first step is to determine whether the issue is software-related, hardware-related, or caused by an external factor such as a corrupted firmware update. A frozen screen can manifest in different ways: the device may not respond to button presses, the display might be stuck on a single screen, or it may fail to power on properly.

Before attempting any fixes, ensure that the Ledger device is receiving sufficient power. Connect it to a known working USB port and observe if there’s any sign of life such as a blinking LED light or a partial screen response. If the device doesn’t power on at all, the problem could be with the battery or internal circuitry rather than a simple software glitch.

Performing a Hard Reset on Your Ledger Device

If the screen remains unresponsive despite being powered, performing a hard reset might resolve the issue. This process varies slightly depending on the model you own—whether it's a Ledger Nano S, Nano X, or Nano S Plus.

For the Ledger Nano S or Nano S Plus:

• Press and hold both buttons simultaneously while connecting the device to a computer.
• Keep holding the buttons until the bootloader screen appears.

For the Ledger Nano X:

• While connected to power, press and hold the two side buttons alternately for several seconds.
• Release them only when the Ledger logo appears.

This action forces the device into recovery mode, bypassing the frozen interface and allowing access to recovery options. It does not erase your wallet but resets the device’s UI state.

Updating or Reinstalling Firmware via Ledger Live

Once the device is in recovery mode, connect it to your computer and open Ledger Live. The software should detect that the device is in recovery mode and prompt you to update or reinstall the firmware.

Follow these steps:

• Ensure Ledger Live is updated to the latest version.
• Click on the notification indicating your device needs firmware recovery.
• Download the latest firmware compatible with your Ledger model.
• Follow the on-screen instructions to install it.

During this process, make sure not to disconnect the device or close the application prematurely. If the firmware installation fails midway, it may result in further issues such as a bricked device or persistent freezing.

Recovering Your Wallet After Fixing the Frozen Screen

After successfully updating the firmware, your Ledger wallet will appear empty because the apps have been removed during the reset. However, your funds are safe as long as you have your 24-word recovery phrase stored securely.

To restore access:

• Open Ledger Live and create a new wallet.
• Choose the option to restore from recovery phrase.
• Enter your 24-word seed phrase carefully.
• Install the necessary cryptocurrency apps (Bitcoin, Ethereum, etc.) back onto your device through Ledger Live.

Your transaction history and balances should reappear once the apps sync with the blockchain. Always verify that the addresses displayed on your Ledger match those shown in Ledger Live to ensure no tampering has occurred.

Contacting Ledger Support for Persistent Issues

If the above steps do not resolve the frozen screen issue, it may indicate a deeper hardware fault or a more complex software corruption. In such cases, contacting Ledger Support directly is advisable.

Prepare the following before reaching out:

• Your device serial number, found on the back of the Ledger or during initial setup.
• A description of the issue including any error messages or unusual behavior.
• Steps you’ve already taken to resolve the issue.

Ledger offers support via email and live chat, though response times can vary. If the device is under warranty, you may be eligible for a replacement. Do not attempt to open or repair the device yourself, as doing so voids the warranty and poses a risk to your private keys.

Frequently Asked Questions

Q1: Can a frozen Ledger screen mean my funds are lost?

No, a frozen screen does not affect your private keys or the funds stored on the blockchain. As long as you have your 24-word recovery phrase, you can recover your wallet on another device or after fixing the current one.

Q2: Is it safe to force restart my Ledger device repeatedly?

While occasional force restarts are safe, repeatedly forcing your Ledger device to reboot without addressing the root cause can lead to firmware instability. Use this method sparingly and follow up with a firmware check.

Q3: How can I prevent my Ledger screen from freezing again?

To minimize the chances of future freezes:

• Keep Ledger Live and firmware updated.
• Avoid installing unsupported third-party apps.
• Store your device in a dry, cool environment away from magnetic interference.

Q4: What should I do if my Ledger Nano X keeps restarting randomly?

Random restarts can indicate battery issues or corrupted firmware. Try reinstalling the firmware using the Nano X recovery process. If the issue persists, contact Ledger Customer Support for diagnostics and potential replacement.